H20 receiver manual

Page 77 4 Electronic protection circuit may have been activated because of a power surge. Wait 30 seconds, then turn on again. If this happens frequently, the voltage in your house may be abnormally high or low. If it does not, check the Setup and Connections section for instructions about connecting your satellite receiver. Page Remote Control Problems Check that nothing is between the remote control and the remote sensor. If you are experiencing any trouble with your receiver, run the system test.

It will also allow you to get your access card and receiver ID numbers or to initiate diagnostic procedures on your digital satellite receiver. Page 83 Display resolutions See Chapter 1 for a full description of screen resolutions, formats, and Native mode.

Page Who Is Covered whichever is deemed necessary if it becomes defective or inoperative. Th is exchange is done without charge to you for parts and labor.

Page 88 Before Requesting Repair Service Please check the troubleshooting section of this guide. To Get Warranty Service Page Product Information Product Information Keep your sales receipt to obtain warranty parts and service and for proof of purchase.

Attach it here and record the serial and model numbers in case you need them. Th ese numbers are located on the product. You may have noted some of this information on page 27 when you connected the cables to your receiver.

Model No. Th is equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to part 15 of the FCC Rules. Page 95 Th e digits represented by are the REN without the decimal point e. If this DIRECTV Receiver causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required.

If the equipment is causing harm to the network, the telephone company may request that you disconnect the equipment until the problem is resolved. Programming subject to change. If you press power button pointing to the device if it powers off then its already programmed and do not need further programming.

If the device is not responding check the batteries in the remote it may be that batteries are exhausted. Use the remote control's mode buttons to set the remote to the correct mode for the equipment. Be sure to program the remote control to operate the other equipment as described on manual.

To change the mode, press the button for the equipment you want to control. The mode button lights for three seconds to show you've set the remote to that mode. Depending on how the remote is set up, the remote control may use UHF radio signals, IR signals, or both to control the receiver. Looking for International Support? Connect ID. What is Connect ID? Call us at Your advisor will be able to share relevant pages and add items to your cart.

Your security and privacy are ensured. Our advisors cannot see anything that is on your computer. They only have the ability to "serve" a page from our site and put items in your cart. All finished with your chat session? Continue chat Close. Our contact center is currently closed. Why is this required? Phone Please enter your US phone number. Please choose one:. For Tech Support, call Begin chat.

Thank you,! Your Advisor,. Order number. Billing zip code. Billing last name. Virtual agent:. No Yes You said. Your phone number. Look up order. Virtual agent: Would you like to schedule a callback from Tech Support? Virtual agent: Thanks! We found your order info. Please fill out the following and we'll have someone from Tech Support call you back at your convenience.

Your phone number Please enter a valid digit phone number. When should we call you back? Callback time. You can exit this chat now. Exit chat Send. Don't wait on hold. We'll call you back when it's your turn to talk with the next available.

How can we help you today? When do you want us to call you back? Schedule a time. Calls may be recorded for training and quality control purposes.

We are located in Virginia USA. Thank you. You are in line to receive a call from. Please keep your phone line open. If you no longer wish to receive the call, please click the button to cancel your request. Move the cursor to the second position. The rubber band line reap- pears, connecting the first point you set to the cursor. The distance along that line will appear in the lower left-hand corner of the screen.

Press to clear the command and return to the page screen. Create Icon at Current Position 1. While you are traveling, press and hold until the screen shows a "Save Icon" menu, then release the key. Page Navigate 1. Page Navigate A Trail 3. If the list is short, you can jump directly to the. To begin navigating to the waypoint, press Navigate a Trail 1.

Routes A route is a series of waypoints, linked together in an ordered sequence, that's used to mark a course of travel. You can visualize a route as a string of beads: The beads represent waypoints and the string repre- sents the course of travel connecting waypoint to waypoint. Page 57 2. Use the Zoom keys and arrow keys to move the map and cursor until the cursor is centered on the spot where you want your route to begin. If you are starting at your current position or the current cursor posi- tion, you are already at the starting spot.

Page Delete A Route 7. You can edit the name if you wish. You could search the entire lodging category, but in this example we will narrow our search. Page Switch To Easy Mode 6. A pop-up name box identifies the POI. A data box at the bottom of the screen continues to display the location's lati- tude and longitude, distance and bearing. Map screen showing Finding Waypoint, 7. This boosts waypoint position accuracy by helping to eliminate errors caused by atmospheric condi- tions and other factors.

Page 66 Notes The factory default setting has all the alarms turned on. You can turn the alarms off and on and change their distance settings. You can set an arrival alarm to flash a warning message and sound a tone when you cross a preset distance from a waypoint.

Page Auto Satellite Search It then searches for only those satellites. When your GPS receiver is turned on for the first time, it doesn't know what your position or elevation altitude is.

The unit begins searching for the satellites using data that it acquired the last time it was turned on. Here's how: 1. While in Advanced Mode press lites" screen. Page Configure Nmea For connectors and wiring information for another device, consult the factory; phone numbers are in the back of this manual. To set Com Port Configuration: 1. Page Coordinate System Selection Coordinate System Selection The Coordinate System Menu lets you select the coordinate system to use when displaying and entering position coordinates.

Access this function only in Advanced Mode. Menus for changing coordinate system used to display positions. To get to Coordinate System Selection: 1. Page Map Fix To select a coordinate system: To change the coordinate system, press highlighted. Press to select it. Press CALE ally at the bottom of the paper map. It's shown as a ratio, for example While we recommend the powerful external active antenna, the unit can operate with an external passive antenna as well.

To do this, you have to let the unit know it's looking for the antenna's signals in a different way. Make the desired settings, then turn the simulator on by highlighting the box and pressing IMULATOR message appears periodically, reminding you that the simulator is on. Page Map Auto Zoom 4. Press to turn off the steering and speed boxes. The unit will now EXIT automatically "steer" along the trail or route.

When you arrive at your "destination," cancel navigation as you normally do. Map Auto Zoom This receiver has an auto zoom feature that eliminates much of the but- ton pushing that other brands of GPS receivers force you to make.

After the option is set, press to return to the page display. All datums are named. Other datums may also cover the entire world, or just a small portion of it.